Mirror 140x70 - Large Rectangular Mirror

Design: Modern
Material: AGC MIROX mirror glass
Lighting: 12V LED 2835, 120 pcs / mb
Mirror glass thickness: 4 mm
Distance from wall: 25 mm
Power supply: 230V
Protection rating: IP67 – 12V power supply, integrated, hidden behind the mirror glass
Component certificates: CE, IP44, CTC, ROHS
Edge finishing: Trapezoidal grinding and polishing
Manufacturer's warranty: 2 years

Tools Needed:
Tape measure
Spirit level
Marking pencil
Electric drill with drill bits suitable for the type of wall (placo, concrete, brick, etc.)
Anchors suitable for the type of wall
Suitable screws
Screwdriver (flat and crosshead)
Hammer
Hole saw (if openings are needed for cables)
Protective gloves
Steps to Fix the 140x70 Mirror to the Wall Without Gap:
Preparation :

Choose the ideal location for your mirror, taking into account alignment and desired height.
Make sure the wall is clean, dry, and free of any irregularities to ensure a perfect fixing.
Measurement and Marking:

Use the tape measure to measure the position of the fixing points on the wall.
Mark the pencil marks accurately using the spirit level to ensure the mirror is perfectly straight.
Preparation of Fixing Points:

Drill holes at the marked locations using the drill and drill bits appropriate for the wall type.
Insert the dowels into the drilled holes. Make sure they are fully inserted and securely fastened.
Installing Wall Brackets:

Attach the mounting brackets supplied with the mirror to the wall plugs using the appropriate screws.
Tighten the screws with a screwdriver or drill to ensure the brackets are secure against the wall.
Mirror Fixing:

With the help of another person, position the mirror on the wall brackets. Make sure it is centered.
Push the mirror firmly against the wall to eliminate any gaps between the mirror and the wall. The mounting system should allow for a snug fit with no visible gaps.
Verification and Finalization:

Use the spirit level to check that the mirror is perfectly straight.
Retighten the screws if necessary to ensure the mirror is stable.
Clean the mirror with a soft cloth to remove any dust or fingerprints left during installation.
Noticed :
If electrical cables will be running behind the mirror, make sure to make the necessary openings before attaching the mirror to the wall. You can use a hole saw to create clean cable runs.

Attention :
The installation of this mirror must be carried out by a professional or someone with DIY experience to ensure a secure fixing that complies with current standards.

Important :
This mirror must be installed in accordance with French standard NFC 15-100, which governs low-voltage electrical installations in buildings. If you are unsure about your ability to carry out the installation safely, it is recommended that you consult a professional electrician.

Safety Distance:
For an electrical connection directly to a power outlet, ensure that you maintain a minimum distance of 60 cm from any water point (sink, shower, bathtub, etc.), in accordance with standard NFC 15-100.

The mirror comes with:
A 5-meter power cable, equipped with an electrical connection plug for quick and easy installation.
Electrical Connection Options:
Direct connection to a power outlet:

Check that the power outlet is located more than 60 cm from a water point.
Simply connect the mirror plug to the power outlet.
Make sure the cable is securely fastened and not hanging dangerously.
Test the mirror by turning on the features (LED lighting, magnifying mirror, etc.) to verify that everything is working properly.
Connection via a Junction Box Behind a Wall:

Choose the ideal location to run the cable behind the wall.
Use a hole saw or drill to make a clean opening for the junction box location.
Cut the power cable to the desired length.
Route the cable through the opening and connect it to an approved junction box, respecting the wire color codes (phase, neutral, ground).
Securely fix the junction box behind the wall, ensuring that it is easily accessible for future maintenance.
Connect the junction box to the main electrical circuit, making sure to turn off the power before handling.
Test the mirror to verify that all features are operational.
Connection by Making a Cut in the Wall:

Determine the exact location of the kerf based on the final location of the mirror and junction box.
Protect the areas around the kerf with masking tape or drop cloths to prevent wall chips.
Use a wall chaser or grinder equipped with a diamond blade to create the groove in the wall.
Cut the cable to the appropriate length and insert it into the groove.
Connect the cable to a junction box behind the wall, following the same instructions as in the previous case.
Fill the groove with plaster or filler, then smooth to prepare the surface for repainting or recoating.
Connect the junction box to the main electrical circuit in accordance with safety standards.
Test the mirror to verify that all features are active.
Noticed :
Ensure all electrical connections are secure and the cable is well insulated to avoid any risk of short circuit or electric shock.

Attention :
When installing an electrical connection in a bathroom, it must be carried out in compliance with the safety zones defined by the NFC 15-100 standard. It is strongly recommended to call upon a professional to ensure a compliant and safe installation.